How to Replace Front Struts Part 1 – EricTheCarGuy
Well I’m finally getting this one up for you, sorry. It’s been a busy week and I just haven’t had the time to finish this one up but here it is in all its glory. Yes, it is something besides a Honda, in fact it’s a 2000 Pontiac Grand Am. I do work on other cars just not that often since I know Honda’s and Acura’s so well. I hope to do a broad range of videos covering a wide range of subjects so keep watching, eventually I’ll get to your request. For now enjoy this video and if you use the spring compressors I did in this video be careful, like I said in the video I’ve seen people get hurt doing this do take it seriously.
Part 2
—
Click below and Stay Dirty
Visit me at EricTheCarGuy.com
Visit EricTheCarGuy Forum
http://www.ericthecarguy.com/forum/default.aspx
Visit my Facebook Page:
http://www.facebook.com/EricTheCarGuy
—
Stay dirty
ETCG
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.
To avoid having to mess with spring compression, you can replace the entire assembly as a unit. That's how I handled a broken a broken spring on my 2000 Grand Am.
Granted, this did cost me nearly double what just the spring would have, but it dodged the safety issue and general annoyance of removing and reinstalling springs and ensured the parts the failed spring would have put the most stress on wouldn't be an issue.
Eric, I want to get a better/smoother ride from my 2006 Ford 500, should I upgrade struts/shocks on front and rear? Or would it be a waste of money? Thank you,,John
"How to change your struts: GONE SEXUAL"
Eric we love you dude
"it's happy to see me'
I died in laughter!😂
Eric I've been a loyal viewer for quite a while now and I gotta say you look terrified doing this job and I was going to attempt this but you make it look scary
I buy the Strut/Coil Spring assembly. Costs me an extra $100 but I get the job done faster and don't risk my life doing it. My well being is worth more than $100.
We need a video for strut removal for a Kia Soul . I can not believe there no Kia Soul videos on removing struts!
Hey Eric, I have front struts that have the two bolts on the bottom to mount. However it looks like they are both set to the right (passenger) side, how to I rotate that bracket to fit on the left (driver) side.?
Can a guy just buy strut/spring assemblies and bypass the difficult/dangerous part?
ok i'm no expert but what i've learned is to loosen the center screw a few turns while it's still on the vehicle just a few turns that way once the spring is compressed it easier to get off
Holy shit. That looks like a disaster waiting to happen. Why would he use such a compressor when there are much better ones that insure the damn thing doesn't slip?
The added safety comments are appreciated
could you just replace the whole assembly? For a home gamer I imagine that would be the most practical and safest way of D.I.Y. without having to spend the money to have it done in the shop
At 4:45, the one you are calling a strut is actually an absorber. The combined spring and absorber is called a strut.
do you have a video on how to replace a 2001 Oldsmobile Alero Thermostat?
Do u have a video on lincoln ls 2006 front strut
You make me happy too Big Guy lol
Have you ever replaced a strut where there is only a single nut up top instead of the common "quick strut"? There are no videos on such strut replacement.
If you don't know what you're doing I would forget this I've seen it done without those compressors I don't know how they did it but it was a murder
NEVER USE AN AIR GUN TO COMPRESS THE SPRINGS!!!
Nice Sooper Troopers reference lol
lmao it was happy to see you.
à ¸Âà ¸£à ¸±à ¹ˆà ¸‡à ¹Âà ¸¡à ¹ˆà ¸¥à ¸¹à ¸Âà ¸£à ¹ˆà ¸§à ¸¡à ¹€à ¸žà ¸¨à ¸Âà ¸±à ¸™
Here I am watching all his old videos, never knowing he's still making new ones.
Man, than you so much for your service to us DIY guys and just people who can can't afford having this kind of stuff done professionally.
Good video.
why cant u use mole grips on new strut??
my compressors look just like yours but they have a little peg that holds the other side. are these any safer?
Hang the strut from the light end when compressing the coil. Holding it top heavy is silly.
I'd rather just replace the entire assembly rather than trying to get that spring off.
Completely newbie question… If just the strut bushing is bad, can you replace it without removing the entire strut by just letting the weight of the car compress the spring?? As a COMPLETE NOVICE at car repairs (although trying to learn), is this feasible or is this asking for trouble? I have a missing bushing on a 2002 Volvo V70 (you can see that it is missing and can be shaken around by hand). I don't know that the entire strut/shock mechanism is bad. From what I am reading, Volvos appear to be notorious for bad strut mounts and bushings in the front… but again, I am a complete novice. I am just poor but really smart and believe I can do just about anything with YouTube as a guide. LOL!!! But those spring compression tools make me nervous as all get out!!! I would almost be tempted to use FOUR instead of two!!! LOL!!!
what is he using to remove the bolts? thanks 🙂