2004 Odyssey Cabin Air Filter Replacement -EricTheCarGuy

This video walks you through the process of replacing the cabin air filter on a 2004 Odyssey. To be honest, you could probably use this for Odysseys dating back to 2000. It also applies to the Acura MDX, Ridgline, and Pilot of the same vintage. If you have this service done it can set you back a few bucks. If you do it yourself, you can save yourself quite a bit and you’ll know that the job was done right. I hope this video helps you if you decide to go that rout. Strangely, I don’t have any extra links for you for this video aside from the usual social network stuff. Enjoy the video!

Discussion about this video: http://www.ericthecarguy.com/kunena/18-The-EricTheCarGuy-Video-Forum/47526-2004-odyssey-cabin-air-filter-replacement#75262

The best place for answers to your automotive questions: http://www.ericthecarguy.com

Facebook: https://www.facebook.com/EricTheCarGuy?fref=ts

Twitter: https://twitter.com/EricTheCarGuy

Google+: https://plus.google.com/100195180196698058780/posts

Information on Premium Membership: https://www.ericthecarguy.com/premium-content-streaming-etcg-content

Stay Dirty

ETCG

Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.

source

Author: avnblogfeed

ANGELHOUSE © 2009 - 2022 | HOSTING BY PHILLYFINEST369 SERVER STATS| & THE IDIOTS ROBOT AND CONTROL INC. |(RSS FEED MODULE)| ALL YOUTUBE VIDEOS IS A REGISTERED TRADEMARK OF GOOGLE INC. THE YOUTUBE CHANNELS AND BLOG FEEDS IS MANAGED BY THERE RIGHTFUL OWNERS (AVNBLOGFEED.COM)

20 thoughts on “2004 Odyssey Cabin Air Filter Replacement -EricTheCarGuy

  1. You dont need to fully remove the steel guard.
    Having removed the right side screws, I just pop the guard up, pivoting off the left most hard to reach screw. I pop the guard up and over the right side plastic fuse cover/wall/carpet pieces, then pivot the guard down to where its just out of the way of the cabin filter cover.
    Remove filter cover, vacuum, install fresh filter, recover, tilt guard back up over the plastic wall bits till its back into position and reattach all screws. Just remove the right side and it saves a lot of frustration.

  2. This 2004 Odyssey is amazingly more complicated than for the two later models, of which I watched videos in case I couldn't find this one. Who thinks of solutions to these puzzles?

  3. Thank you for a great video, I just replaced the cabin filter in our family van with the help of your video. Feeling like a pretty accomplished Mom!

  4. Thanks Eric for the video, I did the job and it went pretty well following your advice. I would only add that you do not need to unscrew completely the bolt on the left under the plastic (6:41 to 7:17 in the video). I had problems putting back the screw after changing the air filter and when I did the job again on another car, I just lose the bolt so that the metal bar can go down and I was able to change the filter without removing that screw completely. It saves a bit of time. Have a good one!

  5. Honda improved the moronic design of this with the 2005 model. I'm in disbelief anyone with an ounce of intelligence would have designed this so poorly.

  6. Suggestions for removing the screw on the right that secures the metal bar when it is stripped ? Tried one of those screw removal tools for the drill (grabit) with no success. Someone had replaced my air filter in the past and managed to help me out this way.

Comments are closed.