Learn how to replace a clutch, flywheel, pressure plate, throw out bearing (aka release bearing), pilot bearing and rear main seal in this video!
My clutch was fine but my throwout bearing was bad so I decided to show how to replace all of the wear items while the transmission was off. This includes replacing the pilot bearing which the transmission input shaft goes into, the throwout bearing which engages the pressure plate via the clutch fork, the flywheel which I upgraded to an aluminum light weight flywheel, and finally the rear main seal because that is a common wear item which causes oil leaks in higher mileage motors. With the transmission out, it is worth it to replace all of these parts now instead of having to do this all over again. Most clutch kits come with the throwout bearing and pilot bearing so you just need to buy a rear main seal.
How to Replace a Transmission (Full DIY Guide): https://www.youtube.com/watch?v=al08aGQTkFk
Thanks Advance Auto Parts for supporting the video.
Flywheel I used: http://bit.ly/aap_flywheel
Clutch kit I used: http://bit.ly/aap_clutch
Rear Main Seal: http://bit.ly/aap_rear_main_seals
→ Become a ChrisFix Subscriber: http://www.youtube.com/subscription_center?add_user=paintballoo7
→ Instagram: https://www.instagram.com/chrisfixit
→ Facebook: https://www.facebook.com/chrisfix8
→ Website: http://www.ChrisFixed.com
→ My Channel Home Page: https://www.youtube.com/ChrisFix
**If the video was helpful, remember to give it a “thumbs up” and consider subscribing.**
Disclaimer:
Due to factors beyond the control of ChrisFix, I cannot guarantee against improper use or unauthorized modifications of this information. ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ChrisFix recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ChrisFix.
I set out to create the most in-depth clutch replacement video in the world! Hopefully the video was helpful!
Follow me on instagram: Instagram.com/ChrisFixit
Because Advance Auto helped out with the parts, if you order parts on their website you can get 25% off at checkout using the code "CLUTCH". I dont make any money off of that, it is all for you guys!
You can get ChrisFix swag here: https://teespring.com/stores/chris-fix
lol i was sure it is a april joke in january xDD with bread
Used all these methods and it worked ðŸ‘Â
How old are u chris
Dam, that clutch is way cleaner that my room
I just subed bro
When the bread came out, I had to check it wasnt uploaded on April 1st.
Nice mustang.
Truly all what clutch needs indeed , nothing missing.
My k5 blazer need pushing replaced ist the same or harder planning to do it my self but scared gna be heavy on me
The last time I had to replace my clutch cable, I added one extra step, I jumpered the very annoying clutch /starter safety switch. None of the older cars had them.
Local mechanistic: this is tied.. I can't get through this
Chris Fix: HoLd My BrEaD
Always a pleasure to watch Chris!
Lettuce 🥬 grease bread ðŸÂž lol
7:11 And bread.
Were you a QVC hand model in a previous life?
You can't replace you're Clutch without Common hAnDtOoLs
Chrisfix: hold my BREAD
Well, now I knew how to align my transmission when replace my clutch😃😃😃
Jeez. This video came in clutch!
NO WAY, u gonna REPLACE all that , when doing a clutch job! If all that needs replacement it better of you trash the CAR and START OVER!
woow ,u are super
i didnt knew that Bread is good for your car
Gotta say Chris you make this all look so simple, but something tells me its really not so easy. I am impressed you know so much.
Sure, I got this
Do you think the clutch kit would work in a 2008 Kia spectra
wet paper towel works too and isn't as messy as the grease and bread method.
good one Chris.
Just a quick tip – if your going to use the "bread and grease" trick to remove the bearing – I've had more luck using an old shop rag rather than bread – seems to seal better
who ever said guys are not clean have not met this guy he got the aluminum shining for sure
What if the input shaft is loose but I'm unable to rebuild the transmission while replacing the clutch?
Lets tighten the bolts in a chris fix pattern
Cool
Im doin my flywheel do I have 2 remove the plate on stock flywheel because it's a aftermarket wheel
Would it be better to change the slave cylinder as well
whe do you make fixing mustang speedometer video?
Hope you get to 10MILLION subs!
You probably won’t see this but if you still have that old transmission can you show us what’s in side of it
So many hungry kids in this world , and we're using Greece and bread on the flywheel .
Think of all the children
Wow! That was awesome! So much in depth knowledge! Thank you! ðŸ˜Â
Hi Chris love the video , am having vibrations problem ( even when standing still when you raise the rpm past 2500 ) in my classic Dodge Charger ( originally auto ) what are the main reasons that can cause this, and if no pilot bushing was installed could that do the vibration . thanks for the help , love the videos !!
Thank you so much sir
he should show a video of how to change your clutch in a fwd car
i want the world to know about you Dr Astrol Goodest for the great work you have done for me i know i was not suppose to say this here i plead, Dr Astrol Goodest is a great man who helped me got back my lover in just 24 hours after me doing what he asked me to do,am sorry Dr Astrol Goodest i onced doubted you i never knew you were this real Dr Astrol Goodest i don't have much to say but a very big thank you from my heart i promise to be loyal to you,and for you reading me now if you need his help too worry no more your solution has come i will advise you also to contact Dr Astrol Goodest via his email [drastrolgoodest@gmail.com] or via his cell phone contact Whatsapp hm +2349135520987 will help you too and promise to thank me later,STAY SAFE AND STAY CLEAN j0
What bread type did you use?
Wouldn't the bread eventually act as a dry debris and increase heat if the transmission isnt serviced properly afterwards?
7:16 ima just leave this here
It’ll be nice if you manufactured your own car 😞.. you damn sure deserve it man!
Youtube recommended this after ,,How to launch manual transmission car"ðŸ‘ÂðŸ¤â€
The bread and grease method was next level. Can we use jam if we run out of grease😜😃
Wonderful job
Thank you so much for sharing